Menu

Ashly KLR-4000 Power Amplifier 2 x (2,000W @ 2) (1,400W @ 4) (850W @ 8) Ohms

Ashly KLR-4000 Power Amplifier 2 x (2,000W @ 2) (1,400W @ 4) (850W @ 8) Ohms

Item Number : Ashly Audio, Inc.

MODEL:ASH KLR-4000

Only 2 left

$920.00
Ashly KLR-4000 Power Amplifier 2 x (2,000W @ 2) (1,400W @ 4) (850W @ 8) Ohms
Add to Wishlist Add to Compare

Ashly KLR-4000 Power Amplifier 2 x (2,000W @ 2) (1,400W @ 4) (850W @ 8) Ohms

Our KLR Series are high-efficiency, high-power 2-channel amplifiers that are the ideal choice for high-output speaker systems, line arrays, dual 18” subwoofers and much more.

If you think you need to use an expensive, European amplifier to get a clean, stable, quiet amplifier—think again. KLRs are quiet with signal-to-noise ratio ratings from >108 dB to >110 dB across all models. They’re also versatile, each with a 3-position gain switch for both channels, a 3-position mode switch (bridged, stereo or parallel mono) and a 3-position 12dB/oct HPF switch (30Hz, 50Hz or off).

Exceptionally lightweight for their class, all KLRs are designed in standard 2RU enclosures. Packed with features, KLRs make a great choice when you need to value engineer a distributed sound system.

  • Rated for 2 Ohms operation
  • Balanced inputs via 3-pin Euroblock
  • Combo XLR/TRS connectors
  • Neutrik® speakON® type output connectors
  • Switch-mode power supply with extensive protection circuitry
  • On/off limiter switch • Forced-air cooled (front-in, rear-out)
  • Removable dust filters, easy to clean
  • Front-mounted attenuators
  • Removable amp handles for permanent installation
  • Optional locking front panel volume knobs
  • Safety/Compliance: cCSAus, CE, FCC, RoHS

 

Architect & Engineering Specs

The two-channel power amplifier shall incorporate the latest amplifier technology to deliver a minimum power of 2,000 Watts per channel into 2 Ohm loads, 1,400 Watts RMS per channel into 4 Ohm loads, or 850 Watts RMS per channel into 8 Ohm loads with both channels operating. The amplifier shall have rear panel switching for parallel mono and bridging modes. When switched into bridged-mono mode, the amplifier shall deliver 4,000 Watts into a 4 Ohm load. The amplifier protection shall include output over-current, DC output, chassis temperature, and a mains circuit-breaker. Frequency response shall be 20Hz–20kHz (1W @ 8 Ohms). The Signal-to-Noise Ratio shall be greater than 109dB at rated power into 8 Ohms (unweighted). THD shall be less than 0.05% into 4 Ohms, 20Hz–20kHz and 10dB below rated power. The amplifier shall have a channel attenuator for each input on the front panel and input sensitivity select switch, a high-pass filter switch and limiter enable switch on the rear panel. The inputs shall be of balanced bridging type with XLR, ¼” TRS, and 3-pin Euroblock connectors. The outputs shall be four pin SpeakON type connectors. LED type indicators shall be employed to show the relative power level of each channel, clip/protect and power on/off. Self contained forced air cooling (front in) shall be used with front panel mounted, removable dust filters. The power amplifier shall weigh 26.7lbs/12.1kg net and mount in a standard 19 inch rack using two spaces (3.5 inches high). The power requirement shall be 120VAC or 240VAC ±10%, 50–60Hz, factory set. 

Write Your Own Review

You're reviewing: Ashly KLR-4000 Power Amplifier 2 x (2,000W @ 2) (1,400W @ 4) (850W @ 8) Ohms

How do you rate this product? *

  1 star 2 stars 3 stars 4 stars 5 stars
Price
Quality
Value

Use spaces to separate tags. Use single quotes (') for phrases.

Related Products